An accessible door usually fails quietly, and the first you hear about it is a complaint. We check your entrances against the standard, fix what is out of range, and leave you written proof it was done. We also handle automatic door repair and storefront door repair across Miami-Dade and Broward, with service in 6 states.
What actually fails on an accessible entrance, answered from the field by Yuval, one of JDM's elite technicians.
When an ADA door stops working, it is either the motor or the push button, the push-to-open actuator people hit on the way in.
People assume an accessible door that has stopped working just needs adjusting or reprogramming.
Either the motor or the push button, meaning the push-to-open actuator. Those two take the wear on an accessible entrance, so they are the first two things we test when a door stops opening the way it should.
Sometimes, but less often than people expect. Adjusting or programming accounts for roughly 10 percent of the accessible-door jobs we run. The other 90 percent needs a part, and it is usually the operator motor or the push-to-open button.
From Gal Cohen, Field Area Manager: "I've spent 15+ years on ada door repair jobs, and our crews now run them across Florida, New York, Georgia, Colorado, Texas and South Carolina. Most repairs we handle wrap up in roughly 2 hours, same-day, and you can see the real before-and-afters in the photos and videos on this page."
ADA problems rarely announce themselves. A closer gets tightened one winter, opening force creeps past what a person using a wheelchair can manage, and the entrance quietly stops being accessible until somebody complains or a claim arrives.
JDM tests and corrects the things the standard actually measures: the force needed to open the door, how long it takes to close, the height and bevel of the threshold, the clear width of the opening, and whether the operating hardware can be worked with a closed fist. Where an entrance needs a powered operator, we repair the push-button and low-energy operators already in place, and replace the ones that cannot be brought back into range.
You get a written record of what was measured, what was adjusted, and what the readings were afterward, which is the document you want on file if anyone ever asks. We are not ADA inspectors and we do not issue certifications. What we do is the measuring and the corrective work, which is usually what a building actually needs.
★★★★★ Verified Google Reviews ★★★★★ · a month ago"After I made an appointment I decided I was going to try and do it myself. Michael FaceTimed me, walked me through what to do, then call back if I still needed him. An hour later I called him and he was at my house in 35 minutes. Some of the best service I've ever received from a contractor. He finished in two hours and went above and beyond. The same-day service was incredible. Absolute professionals."
★★★★★ · a year ago"After a couple of hiccups with getting our repair done by someone else, our technician Richard showed up on time (actually half an hour earlier than the appointment time). He was very polite and got the job done in the time he told us it would take. Our glass door now glides smoothly and is able to lock again. I highly recommend Richard, he represented his company very well. I will definitely consider using them in the future!"
★★★★★ · 9 months ago"David, thank you so much for taking the time to explain everything to us. He was so patient, and I appreciate him doing a clean and awesome job. He was respectful of my home and cleaned up after the work was complete. Now my door slides like new, quiet, and smooth. Again, thank you David."
Visit our Google Business Profile for reviews, hours, and directions.
Opening force with a gauge, closing speed on a timer, threshold height and bevel, clear width, and whether the hardware can be operated with a closed fist.
We show you which readings can be brought into range by adjustment and which need hardware, so you are not quoted an operator for a problem a closer adjustment solves.
We make the adjustments and repairs, then measure again so the numbers on the report are the numbers after the work, not before.
You get the written record of readings and work done, and a plain explanation of anything we could not resolve and what it would take.
Call (954) 689-2155 or request an estimate online. We confirm flat-rate pricing upfront, with no hidden fees.
Our licensed tech arrives with common parts on the truck. Most ada doors jobs are completed in a single visit.
We test the repair, walk you through the work, and make sure everything is running smoothly before we leave.
If your push-to-open button has stopped working, that is the usual suspect.
The operator motor and the push button are the two parts that fail on accessible entrances. Only about one job in ten is solved by adjustment alone.
The actuator people hit on the way in is one of the two parts that fail most on an accessible entrance. We trace the button, the wiring back to the operator, and the operator itself rather than assuming the whole unit is done.
Closing speed is measured from a set angle over a set number of seconds, and closer fluid ages. We reset the sweep and latch speeds so someone slower has time to get through.
We repair the actuator, the wiring, and the operator rather than assuming the whole unit has failed, then set opening speed and hold-open time so the door stays open long enough to be useful.
A threshold that is too tall or squared off stops a wheelchair at the door. We replace or rework it and reseal the opening properly afterward.
Operating hardware has to work with a closed fist, which rules out knobs and tight thumb-turns. We change it for lever or push hardware that meets the requirement.
Doors that will not open far enough, or stops and hardware that eat into the opening. We measure the clear width and correct what is reducing it where the frame allows.
The other of the two most common failures. When the motor has gone, adjustment cannot bring the entrance back into range, so we replace the operator and set it up to the requirement rather than to a default.
We walk every public entrance in a building, measure each one, and hand back a single ranked report so the work can be planned rather than reacted to.
⏱ Same-day service available based on capacity. Call to confirm dispatch.
Opening force, closing speed, threshold height, and clear width get measured first, so you know where the entrance actually stands rather than guessing from how the door feels.
Every visit produces a document showing what was measured, what was adjusted, and the readings afterward. That is the paperwork worth having if a question ever comes up.
When an accessible door stops working it is usually the operator motor or the push-to-open button, not a setting. Adjusting or reprogramming solves about one job in ten. We test the parts that actually fail before quoting anything.
Low-energy and push-button operators are the equipment most likely to be quietly broken. We repair the actuators, wiring, and operators, and set opening speed and hold-open time properly.
We are not ADA inspectors and we do not issue certifications. We measure, we correct, and we document. If your situation needs a certified inspection, we will say so rather than blur the line.
Entrance work happens at the front door, so we schedule around your hours and run after-hours and weekend visits where the entrance cannot be out of service during the day.
JDM handles accessible entrance repair across Florida, New York, Georgia, Colorado, Texas, and South Carolina, with commercial crews dispatched locally in each market.
Tell us what's going on and we'll follow up with a flat-rate quote. Prefer to talk? Call (954) 689-2155.
Ready to fix or upgrade your sliding doors? Contact us today for a free, no-obligation estimate. Our team is available for same-day service.
Call Us(954) 689-2155 Emailoffice@slidingdoorrepairft.comFree estimate. Same-day service available. Flat-rate pricing. No hidden fees.
Here are straight answers to the questions we hear most about ada door repair.
No. We are not ADA inspectors and we do not issue certifications, and anyone telling you a door contractor can certify compliance is overselling. What we do is measure what the standard measures, correct what we can, and hand you a written record of the readings. For most buildings that is what is actually needed.
For interior swing doors, the accessibility standards limit the force to five pounds. Exterior doors vary with local code and are commonly higher. We measure with a gauge rather than by feel, because the difference between a compliant door and a non-compliant one is not something a hand can judge.
Usually yes. Push-button entrances fail at the actuator, the wiring between the button and the operator, or the operator itself, and the first two are repairs rather than replacements. We trace it properly instead of quoting a new operator on sight.
It is, and it is one of the most common ones we find. Closing speed is measured from a set angle over a set number of seconds, and closers drift out of range as their fluid ages. It is often an adjustment rather than a new closer.
Yes. Threshold height and bevel are measurable and correctable, and a threshold is one of the more common reasons an otherwise fine entrance does not work for a wheelchair. We replace or rework it and reseal the opening.
Often, yes, and usually more cheaply than people expect. Adjusting the closer, correcting the threshold, and changing the operating hardware to something workable with a closed fist solves a good number of entrances. Be aware that in our experience adjustment alone is about one job in ten, so budget for the possibility that a part has genuinely failed.
Yes. We can walk a building, measure every public entrance, and give you one report ranking what is out of range and what it would take to correct each one, so you can plan the work rather than react to it.
